Cloud-init on Proxmox VE using debian images

This has been a frustrating experience, so I’m keeping the solution short:

Cloud-init on Proxmox 9.x works with the following Debain cloud images:

  • Bookworm: “generic” images
  • Trixie: “genericcloud” images

The Bookworm genericcloud images fail to locate the Proxmox cloud-init drive.

Post IPTV using a Unifi Security Gateway PRO 4

My friend David asked me to help him tackle a problem with his network. He used a Unifi Security Gateway PRO 4 from Ubiquiti Networks but still wanted to run some Post IPTV STBs on his network. The solution took us some hours spread over several days, but finally the IPTV streams work fine.

Our solution

We ended up using the LAN 2 interface as the IPTV upstream port, it turns out that the Unifi Cloud configuration doesn’t allow a static IP and a PPPoE session on the same interface. Also the built-in WAN-LAN firewall blocking firewall does need adding manual rules to allow the Multicast Traffic back in via the WAN interface. Using LAN2 allowed us to handle Multicast traffic as “Corporate LAN”-to-“Corporate LAN” traffic, which Unifi allows by default, so we can add firewall rules for LAN2 as required using the Unifi Cloud Network Controller instead of using custom JSON files on the Cloud Key. Continue reading “Post IPTV using a Unifi Security Gateway PRO 4”

IPTV on Bamboo with a Mikrotik router

Getting to work an IPTV decoder on a POST Bamboo access with a Mikrotik router instead of Fritz!Box has been one of my long time challenges that I never got around. But finally I got it done, here is how to reproduce it.

I used ether1 port on the Mikrotik to connect to the GPON network termination unit (NTU). As POST uses VLAN 35 as the transport VLAN, i created a vlan interface on top of ether1.

The interface IPTV is a bridge as I distributed IPTV to a VLAN present on several interfaces.

Continue reading “IPTV on Bamboo with a Mikrotik router”

Using a RouterOS to connect to POST LuxFibre

I have used a Routerboard running Mikrotik’s RouterOS to connect to a POST LuxFibre FTTH access for some time. I have been asked in the past to aid with similar setups, so here comes my configuration for the RouterOS CLI.

Note: This setup does NOT (yet) provide access to the Voice service delivered by POST.

In this example I’m using “ether1” to connect to the GPON NTU. (I haven’t yet tested the RouterBoard GPON SFP module, so no need to ask about it 🙂 ) Continue reading “Using a RouterOS to connect to POST LuxFibre”

Why T.38 is not the solution

As VoIP gets more and more popular, it’s users are struggling how to deal with their existing needs for fax services. Some may just connect their fax machine to an analog telephone adapter (aka ATA) and send their fax transmissions via their ITSP. While some may experience random success with this setup, most will experience an unacceptable high failure rate. The T.38 protocol was thought to be THE solution for fax over VoIP as T.38 uses data packets instead of analog modulation but it has its share of issues as well.

So what is the problem? Continue reading “Why T.38 is not the solution”

Changes to the TANGO Blue product

TANGO Blue is TANGO’s counterpart of the EPT LuxFibre. From the start TANGO Blue users received a public IP (compare “No public IP for EPT LuxFibre“). TANGO Blue users weren’t affected by the issues present with LuxFibre. For a while TANGO is now offering an IPTV service on the TANGO Blue access. This combination however provides the user with only a private IP, giving the TANGO Blue+IPTV users the same disadvantages. Several user reports seem to point to TANGO’s CGN, which seems to have difficulties to provide a stable bandwitdh, in some cases reports indicate a reduction of bandwitdh by ~50%. In case you have issues with your TANGO Blue product you should contact the TANGO helpdesk a.s.a.p.